Русский  Казахский  Английский

  • (85594) 4-80-86, 4-90-37, 4-90-48, 4-86-97, 4-91-19

Mortars

ГЛАВНАЯ / Продукция


Econom K-1 Glue

x

This glue is designed for laying tile and ceramic tile on the floor and walls while performing exterior and interior works. It is recommended for external tiling of buildings (except the basement level), for interior works in rooms with normal and high humidity (for bathrooms, balconies, etc.). Econom K-1 Glue is used on such non-deformable foundations as concrete, slag concrete, foam concrete, cement (including cement plaster) and brick. Econom Glue is a reliable and economical tile adhesive. After hardening the glue obtains high strength. The glue does not change its characteristics in direct contact with water and is not susceptible to the effects of freezing temperatures.  
 

Specifications: 5745-002-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-0.27 l.
Layer thickness: 2-15 mm.
Material consumption: 3,6 kg/m2 — 6 mm.
Water solution viability: 180 min.
Correction time: less than 10 min.
Adhesion strength: 0.5 MPa.
Compressive strength: 10 MPa.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Standard K-2 Glue

x

It is designed for laying of ceramic tile, tile, mosaic tile and natural stone tiles on the floor and walls. It is used on such non-deformable foundations as concrete, slag concrete, foam concrete, cement (including cement plaster), brick and plaster (with obligatory priming). Its increased bond strength and high adhesive ability allows to lay tiles top-down preventing sliding. After hardening the glue obtains high strength. The glue does not change its characteristics in direct contact with water and is not susceptible to the effects of freezing temperatures.
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-027 l.
Layer thickness: 3-15 mm.
Material consumption: 3,6 kg/m2 at 6 mm.
Water solution viability: 180 min.
Correction time: less than 15 min.
Adhesion strength: 0.7 MPa.
Compressive strength: 15 MPa.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Elast K-3 Glue

x

It is designed for laying of ceramic tile, tile, mosaic tile and natural stone tiles on the floor and walls. It is recommended for works on such difficult foundations as old tiling, surfaces which heat up to +70°С, underfloor heating systems, as well as for external tiling of buildings (except the basement level), for interior works in rooms with normal and high humidity (for bathrooms, balconies, etc.). Its increased bond strength and high adhesive ability allows to lay tiles top-down preventing sliding. Ready-made glue has high plasticity and is easy to use.
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-0.27 l.
Layer thickness: 2-15 mm.
Material consumption: 3,5 kg/m2 at 6 mm.
Water solution viability: 180 min.
Correction time: less than 20 min.
Adhesion strength: 0.7 MPa.
Compressive strength: 17 MPa.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Hydro K-4 Glue

x

This glue is intended for laying ceramic, glazed and mosaic tiles, tiles made of natural stone (including tiles of larger size and weight) in water reservoirs and rooms with high humidity while performing external and internal works. It is recommended for works on such difficult foundations as old tiling, surfaces which heat up to +70°С, underfloor heating systems, as well as for outer revetment (excepting the basement level), for works in interiors rooms with normal and high humidity (for bathrooms, balconies etc.) It is ideal for laying tile in swimming pools, shower cabins and other interiors with high humidity. Its increased bond strength and high adhesive ability allows to lay tiles top-down preventing sliding. Ready-made glue has high plasticity and is easy to use.
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg..: 0.25-0.27 l.
Layer thickness: 3-10 mm.
Material consumption: 3,2 kg/m2 at 6 mm.
Water solution viability: 200 min.
Correction time: less than 20 min.
Adhesion strength: 1 MPa.
Compressive strength: 12 MPa.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Thermolith K-5 Glue

x

This glue for foamed concrete with lower thermal conductivity is intended for gas- concrete and foam-concrete and polystyrene concrete blocks, sand-lime brick and non-load-bearing clay tile. When diluted an easily spreadable solution is obtained; this solution has higher adhesive and thixotropic characteristics which can be applied either on vertical or horizontal foundations.  It is also good for further filling-up and leveling of walls made of blocks of this kind. It solidifies without contraction and has high adhesiveness with mineral foundations. It has great adhesive characteristics, plasticity, freeze resistance and low thermal conductivity which allows it to conserve heat.
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+35°С.
The amount of water per 1 kg.: 0,19-0,22 l.
Layer thickness: 2-4 mm.
Material consumption: 1,6 kg/m2 at 2 mm.
Water solution viability: 180 min.
Correction time: less than 25 min.
Setting time: 24 hours.
Adhesion strength: 0,3 MPa.
Compressive strength: 5 MPa  in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Theplis K-6 Glue

x

This glue is intended for attachment of polystyrene foam slabs to the walls of the building and for creation of a protective reinforced layer while winterizing building facades. It can be used either for winterization of new buildings or for thermo renewal of old buildings, for winterization  of building facades using mineral-wool and fiberglass plates in order to attach them and for creation of a protective reinforced layer on their surfaces. This glue is used on such stable bases as concrete, slag concrete, foam concrete, cement (including cement plastering), brick, plaster, plasterboard and resin-bonded chipboard base.

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0,27-0,29 l.
Layer thickness: 0,3-3 mm.
Material consumption:  3.5 kg  when using a protective layer.
Water solution viability: 90 min.
Adhesion to concrete: 0,75 MPa.
Adhesion to expanded polystyrene: 0,1 MPa.
Compressive strength: 7,5 MPa  in 28 days.
Flexing strength: 3 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Sh-1 Filling

x

It is used for concrete bases, calcium sulphate and cement plastering, gypsum plasterboard, gypsum-fiber sheets and for any other plaster and cement surfaces that do not require a base, thick-layer coating. It is recommended for the use inside heated rooms with normal humidity. Thanks to the optimal combination of components and polymer additives Sh-1 Filling can be applied in the layer up to 10 mm and to obtain a solid, smooth and non-bleaching white surface. Smooth and non-shrink surface obtained after applying the filling allows to reduce paint consumption and repair expenses. It has high adhesive and crack-resistance characteristics and ensures long-term preservation of the quality of the surface obtained. The obtained vapor permeable surface helps to create a favorable climate in the room.

Specifications: 5745-002-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30 °С.
The amount of water per 1 kg.: 0,40-0,45 l.
Layer thickness: до 10 мм.
Material consumption: 2-5 kg./ 1 m2.
Water solution viability: 120 min.
Curing time: 6-7 hours.
Frost resistance: 35 cycles.
Compressive strength: not less than 0,2 MPa.
Adhesion strength: 0,4 MPa.
Storing period: 12 months.

CONFORMITY CERTIFICATE


T-1 Machine Applied Plaster

x

It is ideal for leveling of walls and ceilings in rooms with normal humidity for subsequent finishing which is ceramic tile laying, wallpapering, painting, etc. using plaster machine. Surface finishing in humid heated premises is possible only with further ceramic tiling and careful toweling of tile joints.
This plaster is used for concrete, foam concrete, gypsum and cement-sand bases, brick masonry, as well as for other non-deformable bases.

GOST: 31377-2008
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-0.27 l.
Layer thickness: 5-30 мм.
Material consumption: 8-9 kg/m2 at 10 mm.
Water solution viability: 120 min.
Adhesion strength: 0.4 MPa.
Compressive strength: not less than 5 МПа.
Initial setting time: no earlier than 90 минут.
Storing period: 12 months.

CONFORMITY CERTIFICATE


T-2 Plaster

x

It is ideal for leveling of walls and ceilings in rooms with normal humidity for subsequent finishing which is ceramic tile laying, wallpapering, painting, etc. It has high vapor-permeable and low thermally-conducting characteristics which help to create a favorable microclimate in the room. It has high adhesive and crack-resistance characteristics and ensures long-term preservation of the quality of the surface obtained. Smooth and non-shrink surface obtained after applying the filling allows to reduce paint consumption and repair expenses. Excellent glossing ability and the white color of plaster makes final leveling possible without further application of final filling.

Specifications: 5745-002-43819168-07
Packaging option: 30 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0,50-0,60 l.
Layer thickness: до 50 мм.
Material consumption: 2-5 kg/m2
Water solution viability: 90 min.
Время корректировки: not less than 30 min.
Время твердения: 5-7 days.
Adhesion strength: 0.4 MPa.
Compressive strength: 5 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


T-3 Plaster

x

It is used for leveling of surfaces of building facades and structures above the basement level without a lath in the layer up to 30 mm, and also for repairing splits, pot holes, cavities and cracks in the layer up to 60 mm. Manual and machine application in external and interior works. Recommended bases: concrete, foam concrete, brick, sand-cement, gas silicate and other non-deformable surfaces. It has high adhesive and crack-resistance characteristics and ensures long-term preservation of the quality of the surface obtained.

 
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0,18-0,21 l.
Layer thickness: до 5-30 мм.
Material consumption at 10 мм: 12-16 kg/m2
Water solution viability: 120 min.
Время твердения: 24 hours.
Adhesion strength: 0,4 MPa.
Compressive strength: 9 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


PN-1 Cement Screed

x

It is used for preparation of solid, flat bases (screed coat) for subsequent laying of laminate flooring, parquet, linoleum, ceramic tile, layering of thin self-leveling dandy rolls and other floor coatings. It is used both for interior and external works in dry premises and the ones with high humidity and also for underfloor heating systems. This screed is used for concrete and cement mortar bases which were made not less than 28 days ago. The product is economical and of high-quality, it is easily mixed and applied what makes it profitable and easy to use.
 
 
 
 

Specifications: 5745-001-43819168-07
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-0.28 l.
Layer thickness: 10-50 мм.
Material consumption at 10 мм: 20 kg/m2.
Water solution viability: 120 min.
Время твердения: 5-6 hours.
Время пешего хождения: 2-5 days.
Adhesion strength: 0,3 MPa.
Compressive strength: 20 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


PN-2 Self-Leveling Floor

x

It is used for high-quality leveling of horizontal foundations (cement screed, cement floor with heating; concrete, floor tiled with ceramic or marble tiles) inside houses, offices and municipal facilities before laying of floor coatings made of ceramic tile, ceramic granite, glass mosaic, natural stone tile, parquet, linoleum, textile carpeting and etc. on bearing foundations with significant (up to 10 mm) differences or imperfections. It is also used for final thin-layer leveling (from1 mm) of cement screeds and other recommended foundations with minor imperfections. It is used in underfloor heating systems and possesses a self-leveling property.

 

Specifications: 5745-003-43819168-08
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.28-0.3 l.
Layer thickness: до 10 мм.
Material consumption at 10 мм: 20-22 kg/m2.
Water solution viability: 30 min.
Время твердения: 2-7 days.
Adhesion strength: 0,6 MPa.
Compressive strength: 15 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


PN-3 Self-Leveling Floor

x

It is used for high-quality leveling of horizontal foundations (cement screed, cement floor with heating; concrete, floor tiled with ceramic or marble tiles) inside houses, offices and municipal facilities before laying of floor coatings made of ceramic tile, ceramic granite, glass mosaic, natural stone tile, parquet, linoleum, textile carpeting and etc. on bearing foundations with significant (up to 100 mm) differences or imperfections. It is also used for final thin-layer leveling (from 2 mm) of cement screeds and other recommended foundations with minor imperfections.

 

Specifications: 5745-003-43819168-08
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0,27-0,28 l.
Layer thickness: до 100 мм.
Material consumption: 22 kg/m2.
Water solution viability: 30 min.
Время твердения: 2-7 days.
Adhesion strength: 0,3 MPa.
Compressive strength: 15 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


M-150 Masonry Admixture

x

It is used for stone and brick masonry in the construction of residential, industrial, municipal and agricultural buildings and constructions made from single-piece materials (brick, stone, concrete blocks and etc.). It ensures high strength at hardening. Binding qualities of this admixture make it suitable for the erection of foundations from factory-made elements, as well as for basic floor arrangement. It is used for internal and external works.
 
 
 
 
 
 

Specifications: 5745-003-43819168-08
Packaging option: 25 kg.
Application temperature range: +5-+30°С.
The amount of water per 1 kg.: 0.25-0.27 l.
Layer thickness: до 10 мм.
Material consumption: 1 kg/m2.
Water solution viability: 120 min.
Curing time: 48-12 hours.
Adhesion strength: 0,6 MPa.
Compressive strength: 15 MPa in 28 days.
Frost resistance: 35 cycles.
Storing period: 12 months.

CONFORMITY CERTIFICATE


Econom K-1 Glue
TriS brand
Standard K-2 Glue
TriS brand
Elast K-3 Glue
TriS brand
Hydro K-4 Glue
TriS brand
Thermolith K-5 Glue
TriS brand
Theplis K-6 Glue
TriS brand
Sh-1 Filling
TriS brand
T-1 Machine Applied Plaster
TriS brand
T-2 Plaster
TriS brand
T-3 Plaster
TriS brand
PN-1 Cement Screed
TriS brand
PN-2 Self-Leveling Floor
TriS brand
PN-3 Self-Leveling Floor
TriS brand
M-150 Masonry Admixture
TriS brand